TC4钛合金盘铣开槽加工残余应力
作者:
作者单位:

1.湖北文理学院 纯电动汽车动力系统设计与测试湖北省重点实验室,襄阳 441053;2.西北工业大学 现代设计与集成制造技术教育部重点实验室,西安 710072

作者简介:

辛红敏,1979出生,博士,主要研究方向为复杂曲面数控加工。E-mail:xhm0330@163.com

通讯作者:

中图分类号:

TG506.7

基金项目:

高档数控机床与基础制造装备科技重大专项(2013ZX04001081,航空发动机整体叶盘高效强力复合数控铣床开发及应用);中国博士后面上资助(2018M631195,航空发动机整体叶盘盘铣开槽加工技术);湖北省技术创新专项重大项目(2017AAA133)


Residual Stress of Disc-Milling Slotting of TC4 Titanium Alloy
Author:
Affiliation:

1.Hubei Key Laboratory of Power System Design and Test for Electrical Vehicle,Hubei University of Arits and Science,Xiangyang 441053;2.The Key Laboratory of Contemporary Design and Integrated Manufacturing Technology,Ministry of Education,Northwestern Polytechnical University,Xi’an 710072

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    整体叶盘盘铣开槽加工过程中铣削力大,铣削温度高,会在加工表面表成较深的残余应力层,对零件的疲劳寿命造成严重影响。为提高零件的疲劳寿命,本文以钛合金试块为研究对象,利用残余应力测试分析系统测量表面残余应力,利用拨层法测量次表面的残余应力,采用线性回归技术建立残余应力预测模型,并利用极差分析法分析工艺参数对残余应力的影响规律。试验结果表明:盘铣表面均为压应力,且轮毂面上的残余应力大于叶盆叶背面上的残余应力,均由挤光效应引起;回归预测模型的显著性水平为0.01,其回归效果良好;各因素对σAx、σAyAx、σAy 分别表示轮毂面x、y方向残余应力)的影响程度依次为主轴转速>进给速度>切削深度;对σBx (σBx 表示叶盆叶背面x方向上的残余应力)的影响程度依次为主轴转速>切削深度>进给速度;残余应力纵向均为压应力,轮毂面上的分布深度为230~270 μm,叶盆叶背面上的分布深度为170~175 μm。

    Abstract:

    In the process of disc milling grooving in blisk,the milling force is large and the milling temperature is high,these factors will form a deep residual stress layer on the machined surface,which will seriously affect the fatigue life of the parts.In order to improve the fatigue life of parts,based on the titanium alloy block as the research object,the surface residual stress is measured by the residual stress test analysis system,and the subsurface residual stress is studied using the dial layer method.The linear regression technique is adopted to establish the prediction model of residual stress,and the range analysis method is used to analyze the influence law of process parameters on the residual stress.The test results show that the residual compressive stress are generated on the machined surface caused by extrusion effect,and the residual stress on hub surface is greater than that on the convex/concave surface. The significance level of the regression prediction model is 0.01,and the regression effect is good.The influence degree of each factor on σAx 、σAy (σAx 、σAy represent residual stress in x and y directions of hub surface respectively) is spindle speed>feed speed>depth of cut (DOC) respectively.The influence degree of each factor on σBx (σBx refers to residual stress in the x direction on the convex/concave surface) is in turn spindle speed>DOC>feed speed respectively.The longitudinal residual stress is compressive stress,the distribution depth on the hub surface is 230 to 270 μm,and the distribution depth on the convex/concave surface is 170 to 175 μm.

    参考文献
    相似文献
    引证文献
引用本文

辛红敏,吴华伟,杨峰,王琳. TC4钛合金盘铣开槽加工残余应力[J].宇航材料工艺,2020,50(1):71-78.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2019-04-12
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2020-02-17
  • 出版日期:
第十一届航天复合材料成形与加工工艺技术中心交流会 征文通知

关闭